Additional Product Information
Magna-Power Electronics TS Series combines
the best of DC power processing with microprocessor embedded
control. Magna-Power Electronics' innovative power processing
technology improves response, shrinks package size, and
reduces cost. TS Series power supplies are current-fed and are
more tolerant to abusive loads than conventional switching
power supplies. This technology allows the power supply to
operate under short-circuit conditions, open-circuit
conditions, and everything in between.
TS Series power supplies offer both master/slave parallel
and series operation. This enables two or more power supplies
to be placed in parallel for increased output current or in
series for increased output voltage. With master/slave
operation, power supplies operate at near equal voltage and
current.
TS Series power supplies can operate as a voltage source or
current source depending on the control settings and load
conditions. If the power supply is operating as a voltage
source and the load increases to a point beyond the current
command setting, the power supply automatically crosses over
to current mode control and operates as a current source at
that setting.
TSA Version Front Panel
TSA models provide stepless analog control from front
panel knobs. With a simple configuration change, the power
supply can be programmed from the rear I/O connector or
through software on one of the communication buses.
TSD Version Front Panel
TSD models provide all of the features of the TSA Version
plus these models can be configured for keypad entries and
up/down presses for voltage, current, over voltage trip, and
over current trip. Key strokes are kept to a minimum by a
repeat last command feature. TSD Series power supplies are
well suited for laboratory applications requiring enhanced
control.
TSD Series models have one-hundred memory states available to
program voltage, current, over voltage trip, over current
trip, and time period. Set points can be auto sequenced with
time or external triggering. Special programming codes allow
repeating to create a power function generator. The first 10
memory states are displayed on the front panel to simplify
programming tasks. TSD Series power supplies offer an analog
input to modulate the voltage or current setting using
piecewise linear approximation. This feature enables the
voltage or current setting to be adjusted by a sensor input,
such as a thermistor, or by monitoring its own voltage or
current. Modulation allows the output to be tailored for
advanced process control applications, battery charging, and
source emulation.
TSC Version Front Panel
TSC models hava a blank front panel and only allows
control from the rear I/O connector or by RS-232/GPIB/USB/Ethernet
communications. These models are intended for process control
applications where front panel controls and displays are not
required nor desired.
Optional Water Cooling (must be specified at time of
order)
Optional water cooled models contain integrated semiconductor
chillers and air to water heat exchangers to manage cooling of
heat producing components. This option allows the power supply
to be sealed from the environment enabling placement in harsh
environments. These units provide long life in plating
facilities, electrodionization treatment plants, shipboard,
and other corrosive environments. Water cooling also permits
power supplies to be stacked in high density equipment racks
where air cooling is not possible or desirable.
Flexible Operation and Programming
The power supply can be programmed to have its control
functions accessible from the front panel (except TSC Models),
rear connector, or through RS-232, optional GPIB, or optional
LAN (LXI-C) communications with built-in webserver. USB and
RS-485 converters are also available. TS Series power supplies
incorporate an optically isolated feedback system. The result
is that all user interface circuitry is referenced to earth
ground -- not the negative terminal of the power supply. This
enables users to connect external circuitry without concern of
ground loops or voltage breakdown.
Remote
Interface Software
The Remote Interface Software is shipped with all TS SERIES
power supplies. The software provides the user with a quick
method to operate a Magna-Power Electronics' power supply
under computer control. The Remote Interface Software has six
windows: the Virtual Control Panel, Command Panel, Register
Panel, Calibration Panel, Firmware Panel, and Modulation
Panel. The Virtual Control Panel emulates the front panel of
the TS SERIES power supply, the Command panel programs and
reads SCPI commands with user friendly buttons, the Register
Panel programs and reads registers, the Calibration Panel
enables calibration of the digital potentiometers, the
Firmware Panel enables the program stored internal to the
power supply to be upgraded, and the Modulation Panel eases
programming of modulation parameters.
Standard Voltage and Current Ratings
| Voltage (V) |
Current (A) |
| 5 kW Models |
10 kW Models |
15 kW Models |
20 kW Models |
25 kW Models |
30 kW Models |
45 kW Models |
| 0-5 |
900 |
n/a |
n/a |
n/a |
n/a |
n/a |
n/a |
| 0-8 |
600 |
n/a |
n/a |
n/a |
n/a |
n/a |
n/a |
| 0-10 |
500 |
n/a |
n/a |
n/a |
n/a |
n/a |
n/a |
| 0-16 |
300 |
600 |
900 |
1200 |
1500 |
1800 |
2700 |
| 0-20 |
250 |
500 |
750 |
1000 |
1250 |
1500 |
2250 |
| 0-32 |
150 |
300 |
450 |
600 |
750 |
900 |
1350 |
| 0-40 |
125 |
250 |
375 |
500 |
625 |
750 |
1125 |
| 0-50 |
100 |
200 |
300 |
400 |
500 |
600 |
900 |
| 0-80 |
62 |
125 |
186 |
248 |
310 |
372 |
558 |
| 0-100 |
50 |
100 |
150 |
200 |
250 |
300 |
450 |
| 0-125 |
40 |
80 |
120 |
160 |
200 |
240 |
360 |
| 0-160 |
31 |
62 |
93 |
124 |
155 |
186 |
279 |
| 0-200 |
25 |
50 |
75 |
100 |
125 |
150 |
225 |
| 0-250 |
20 |
40 |
60 |
80 |
100 |
120 |
180 |
| 0-375 |
13 |
26 |
39 |
52 |
65 |
78 |
117 |
| 0-400 |
12 |
24 |
36 |
48 |
60 |
72 |
108 |
| 0-500 |
10 |
20 |
30 |
40 |
50 |
60 |
90 |
| 0-600 |
8 |
16 |
24 |
32 |
40 |
48 |
72 |
| 0-800 |
6 |
12 |
18 |
24 |
30 |
36 |
54 |
| 0-1000 |
5 |
10 |
15 |
20 |
25 |
30 |
45 |
| 0-1500 |
3.3 |
6.6 |
9.9 |
13.2 |
16.5 |
19.8 |
27.7 |
| 0-2000 |
2.5 |
5 |
7.5 |
10 |
12.5 |
15 |
22.5 |
| 0-3000 |
1.6 |
3.2 |
4.8 |
6.4 |
8 |
9.6 |
14.4 |
| 0-4000 |
1.2 |
2.4 |
3.6 |
4.8 |
6 |
7.2 |
10.8 |
Input Voltage (Must be specified at time of order)
1 phase, 2 wire + ground (5 kW, 10 kW, and 15 kW models
only)
208 VAC, 1 φ (operating range 187 - 229 VAC) add $100
240 VAC, 1 φ (operating range 216 - 264 VAC) add $100
3 phase, 3 wire + ground (all models)
208 VAC, 3φ (operating range 187 - 229 VAC)
240 VAC, 3φ (operating range 216 - 264 VAC)
380 VAC, 3φ (operating range 342 - 418 VAC)
415 VAC, 3φ (operating range 373 - 456 VAC)
440 VAC, 3φ (operating range 396 - 484 VAC)
480 VAC, 3φ (operating range 432 - 528 VAC)
Model Number Example:
TS Series, A Version front panel, 40 Volts, 375 Amps, 480 VAC
3φ input
TSA40-375/480
TS Series, A Version front panel, 40 Volts, 375 Amps, 240
VAC 1 φ input
TSA40-375/240SP
NOTE:
- Models over 15 kW are intended for rack mount
installations only. They are not designed for benchtop use
due to exposed input and output terminals.
- GPIB and Ethernet are optional and must be specified
at time of order.
- Power cords are not included.
